Check Engine Light

Why Is My ABS And Traction Control Light On? What Should You Do?

Mike Cross
Updated Mar 26, 2023
abs and traction control light on

Today's modern cars have been equipped with an anti-lock braking system, or ABS for short. This feature has proven to be a crucial piece of safety equipment in cars by helping reduce the braking distance and provide added traction in low-grip situations.

Because the ABS and traction control systems are one module and use the same sensors, if one fails, the other will likely cease as well.

This article will help you understand what the ABS system does, how it operates, what may cause it to fail, as well as answer a host of other ABS related questions.


What is an ABS system and how does it operate?

If your wheels lock-up under hard braking conditions, your stopping distance is greatly increased. The ABS system takes notice of that and releases the brakes in a sort of “pulsing” fashion to decrease the overall braking distance.

Comparing ABS and non-ABS car

How does the traction control system work? 

Alternatively, if accelerating in slippery conditions, chances are the vehicle will break traction with the road. In the event of that happening, the traction control system kicks in by reducing the engine's power to help the driver regain grip.

Common ABS/Traction Control Light Faults

abs and traction control light on
Why Is My ABS And Traction Control Light On

If your ABS/Traction Control light turns on, it most likely means that these safety systems are no longer active. Have no fear, the car will still run and function perfectly fine, but greater caution should be taken while driving. Let’s have a look at some of the most common faults associated with the ABS/Traction Control light being on.

Defective Wheel Spin Sensor

Wheelspin sensors, or calling by wheel speed sensors measure the rate at which the wheel spins which is then relayed to the ABS/Traction Control module. If one wheel is spinning faster than any of the rest, the car will then cut power to the engine until traction is regained.

A defective sensor will likely disable the system and the driver will be left up to their own to try and regain traction. Common indications of a defective wheel speed sensor are excessive wheel spin when taking off from a standstill.

Defective Steering Angle Sensor

As you might have guessed, the steering angle sensor is responsible for measuring the angle of the steering wheel. Another job the sensor has is to track the speed at which the wheel is turned.

For the traction control system to work correctly, the vehicle must know where the driver is intending to go. If this sensor fails, the car effectively is left without traction control, but be careful as this issue might also be disguised as a bad clock spring.

Faulty ABS/Traction Control Module

In rare cases, the module controlling the ABS/Traction control may fail, leaving you, the driver, without any traction control or anti-lock brake aids. While this might sound extreme, it is not so bad if the road conditions are dry.

As you might have guessed, the ABS/Traction Control module takes the incoming signals from the sensors and decides when to intervene. Think of it as a second pair of eyes that is ready to help out at any moment.

System Malfunction

Sometimes, one or several of the sensors get overran with so much information they will essentially freeze up. This will trigger the warning light on your dash and the ABS/Traction Control features will no longer work.

Poor Connection

This issue is encountered quite often, many times after having work done around the wheels. It’s good to keep in mind that this is not always the case.

If no recent wheel work has been performed, it may be possible that the connections have simply worked themselves loose over the years. In worst-case scenarios, the wires leading to the sensors can get severed due to excessive rubbing.

Repairing Common Faults

Wheel Speed Sensors

A wheelspin sensor can become easily damaged due to them being exposed to the elements over the years. Usually, they are located on the brake assembly of the vehicle and can be easily replaced.

To replace the sensor, you must first locate it and the easiest way to do that is by removing the wheel. After it is located, simply disconnect the wiring going to it and replace it with a new one.

This video describes how to replace the wheel speed sensors

Steering Angle Sensor

The location of a steering angle sensor varies on each vehicle. It can be located behind the steering wheel, close to the steering box, or near the wheels, just like the wheel speed sensor.

Depending on where it is located will determine the difficulty of replacing the sensor. A simple Google search will tell you exactly where it on your car. Replacing it can be as simple as unplugging the old one and plugging a new one in. It is important to know that sometimes the sensor may just need recalibration.

Faulty ABS/Traction Control module

Car Disc Brake

On most vehicles, the ABS/Traction Control module is located under the hood next to the brake fluid reservoir. It is easy to spot thanks to its large, square size and several hard brake lines that lead to it.

Replacing the module itself should be a last resort, as it can be quite difficult and expensive to replace. Be sure you have the proper tools and knowledge before attempting this job. If the new module matches up to the old one, simply take off all connections from the old one and install the new unit in place. Once done, a brake bleed operation must be performed to ensure there are no air bubbles in the system.

Improper Connection

Often, the wires leading into a sensor may have come loose, thus not making proper contact with the sensor. This issue can be resolved by making sure the connector is set securely in place.

To save you some time, scanning the car for faults with an OBD2 code reader such as this one is recommended as this will point you in the right direction.

While most automotive manufacturers use specific fault codes for their vehicles, they are sometimes interchangeable between most models. For example, codes ranging between C0031-C003E mean that one of the speed sensors is malfunctioning on a Ford/Lincoln.

Similarly, a wheel speed sensor on most Toyota models will be P0500.


Having your Traction Control/ABS light turn on can be the cause of several problems, some requiring little just a simple restart, while others can take up a lot of time and money.

The best way to figure out why the warning light has been turned on in the first place is to scan the vehicle for fault codes. After all, no one wants to replace a part that isn’t broken.

We hope that this article helped shed some light on why the ABS/Traction Control light is on in your car and be sure to check out our other articles to help you with our other car-related issues!

Mike Cross
Life is too short to drive with stock audio

Leave a Reply

Your email address will not be published. Required fields are marked *

59 comments on “Why Is My ABS And Traction Control Light On? What Should You Do?”

  1. Hello Mike,

    My BMW 1 Series has just started juddering on start up I am having to re-start the engine so it re-sets itself. Also the Icon with the circle with an A in the middle is flashing and the car has started to almost judder to a holt as if I am braking inconsistently, any ideas?? - I rang a garage who said it could be the injectors or the Traction Control? Any help would be appreciated.

    Kind Regards

  2. I've just had my car MOTED and they put me 2 back tyres on . And now I have the ABS & Traction control lights on and they stay on and I don't know why . Help please

  3. I have a 2001 Cadillac El Dorado ESC that had been garaged and not driven for about 5 years. This was a one original owner car from an elderly person. I replaced Tires, best oil change, water pump, new battery but I have the ABS and Traction Control lights that come on and off. Then on the dashboard message it is saying "Service Stability Systems." What can it be?

  4. I was driving when my ABS light came on for the 1st time. Then I wasn't able to accelerate. When I try it feels like I am holding my foot when my brake pedal and trying to accelerate in the tires just will not go anywhere now my traction stability light is 1 what could cause this my car is stuck in my driveway and I have no way to get to repair shop

  5. My 2006 325i, abs, traction control, brake no radio, no cigarettes lighter electricity.about 2 months ago a guy changed my starter, but starter was not the problem, than he did some wiring work with fuel pump. After that work all these light coming in dash board. What could be the possible problems?
    Please help me with this.
    Thank you


  6. Hello, I have a 2005 Honda Accord and my TCS light came on after a collision center repaired my bumper. I'm not sure if the repair center did something wrong or not. Can you offer any suggestions?

  7. dear Mr.
    good day
    I have problem with my ford escape 2008 ABS and battery light's are on.
    I need to talk the batter wire off the safe power. and it will stop working after 2 to 3 mins

    please cave me any bits of advice to try to solve the problems

  8. Have had this problem with mine and after replacing sensor and wheel bearing found it to be a bad GROUND off of the battery

  9. Could the ABS, Brake System light and Traction control lights come on to alert you to replace the brake pads by any chance?

linkedin facebook pinterest youtube rss twitter instagram facebook-blank rss-blank linkedin-blank pinterest youtube twitter instagram